Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected
by the drive itself and contains data that the manufacturer considered relevant to check reliability.
The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data,
and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is
considered unreliable and likely to fail. By using several techniques, this report tries to give a wider
range of information, basing its analysis on advanced comparisons with normal values based on real
hard disks and on expert-like checks. The final results are not to be taken as an absolute truth, but
they are almost as good as a professional expert advice about your hard disk status.
Your hard disk is a SAMSUNG HD502HJ with firmware 1AJ100E4.
The average temperature for this hard disk model is 31°C (min=23°C max=40°C) and yours is 26°C.
All the attributes of your hard disk are above the S.M.A.R.T. thresholds set by the manufacturer. This is good.
BLOCKING ISSUE : your hard disk has 2 pending sectors. Those are sectors that couldn't be properly read and that the hard disk logic is waiting for a write operation to try to remap to a spare sector (if available). According to the Reallocated Sector Count attribute, your hard disk seems to have available spare sectors. A simple disk surface scan won't be enough to force the remap operation. You need a read/write surface scan to remap the sector. The best option should be a tool that knows about what should be read from that sector so that it has some option to apply the best fix to the missing data.
NOTE : your hard disk Power Cycle Count attribute current value (98) is below the normal range (100 - 100) reported for your specific hard disk model. Basically your hard disk was power cycled more times than the maximum number the average hard disk was. Power cycles put some stress on the hard disk mechanic. Sometimes power cycles can be caused by a loose hard disk power connector. Make sure it is properly fastened.
The overall fitness for this drive is 0%.
The overall performance for this drive is 90%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
DISCLAIMER: this report does its best to highlight issues and warnings related to your hard disk. It cannot be held responsible for any mistake. This page and its results cannot be used in any other way but the one defined by its author.
The average temperature for this hard disk model is 31°C (min=23°C max=40°C) and yours is 26°C.
| Attribute | Current | Raw | ||||
|---|---|---|---|---|---|---|
 |
Raw Read Error Rate | 100 | 00000000036F | |||
 |
Throughput Performance | 252 | 000000000000 | |||
 |
Spin Up Time | 83 | 000000001478 | |||
 |
Start/Stop Count | 98 | 000000000A16 | |||
|
Reallocated Sector Count | 252 | 000000000000 | |||
|
Seek Error Rate | 252 | 000000000000 | |||
|
Seek Time Performance | 252 | 000000000000 | |||
|
Power On Hours Count | 100 | 000000003268 | |||
|
Spin Retry Count | 252 | 000000000000 | |||
|
Calibration Retry Count | 252 | 000000000000 | |||
|
Power Cycle Count | 98 | 000000000BD1 | |||
|
GSense Error Rate | 252 | 000000000000 | |||
|
Power Off Retract Count | 252 | 000000000000 | |||
|
Hardware ECC Recovered | 100 | 000000000000 | |||
|
Reallocated Event Count | 252 | 000000000000 | |||
|
Current Pending Sector | 100 | 000000000002 | |||
|
Offline Uncorrectable Sector Count | 252 | 000000000000 | |||
|
Ultra DMA CRC Error Rate | 100 | 000000000001 | |||
|
Write Error Rate | 100 | 000000000000 | |||
|
Load Retry Count | 252 | 000000000000 | |||
|
Load Cycle Count | 100 | 000000000C32 |
All the attributes of your hard disk are above the S.M.A.R.T. thresholds set by the manufacturer. This is good.
BLOCKING ISSUE : your hard disk has 2 pending sectors. Those are sectors that couldn't be properly read and that the hard disk logic is waiting for a write operation to try to remap to a spare sector (if available). According to the Reallocated Sector Count attribute, your hard disk seems to have available spare sectors. A simple disk surface scan won't be enough to force the remap operation. You need a read/write surface scan to remap the sector. The best option should be a tool that knows about what should be read from that sector so that it has some option to apply the best fix to the missing data.
NOTE : your hard disk Power Cycle Count attribute current value (98) is below the normal range (100 - 100) reported for your specific hard disk model. Basically your hard disk was power cycled more times than the maximum number the average hard disk was. Power cycles put some stress on the hard disk mechanic. Sometimes power cycles can be caused by a loose hard disk power connector. Make sure it is properly fastened.
The overall fitness for this drive is 0%.
The overall performance for this drive is 90%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
DISCLAIMER: this report does its best to highlight issues and warnings related to your hard disk. It cannot be held responsible for any mistake. This page and its results cannot be used in any other way but the one defined by its author.